Renault Clio III Door sealing film Removal – Refitting
download
REMOVAL a Note: The sealing ?lm can only be used once; it is des- troyed when it is removed. It is essential to replace the ?lm with a new one each time it is removed. REMOVING THE SEALING FILM a Remove the door trim( (see Front side door trim: Removal – Refitting) (MR 393, 72A, Side opening elements trim) or( (see Rear side door trim: Remo- val – Refitting) (MR 393, 72A, Side opening ele- ments trim). a Start with the upper section of the sealing film. a Remove the heptane in small amounts between the film and the inner door panel as the film peels away (pull slowly on the sealing film). a Carefully strip off the sealing film taking care not to tear it. REFITTING a Note: Remove the adhesive residue from the inner door panel by sticking wide masking tape over the adhesive residue. Pull gently on the masking tape to remove any adhesive residue. Clean the inner door panel with heptane using a dr y, lint-free cloth. WARNING The door must be clean (free of dust, grease, anti-adhesive products), with no trace of impuri- ties and no condensation. The area of the inner door panel where the ?lm is applied must be painted completely. Adhesive surfaces should be at a minimum tem- perature of 15? in order for the ?lm to adhere pro- perly to the door. 116833 a Unclip the interior handle mounting (if the vehicle is fitted with one) using an unclipping tool. 1 – First procedure a Strip off the sealing film using a hot air gun set to ap- proximately 100? and approximately 20 cm from the film, directing the hot air flow onto the edge of the film. a Start by stripping off a corner of the sealing film. a Carefully strip off the sealing film taking care not to tear it. 2 – Second procedure a Remove the sealing film using a syringe filled with heptane. Front side door ACCESS FLAP 1 – Opening access flaps front side door 111932 Rear side door a Note: The front side door sealing ?lm incorporates two access ?aps to access the various door compo- nents and to allow the door to be straightened. Cut according to the marking on the sealing ?lm depending on the operation being performed. Depending on the operations being performed, it may be necessary to make cuts locally at the various mountings (bolts or nuts). 111945 a Position the sealing film using the guide points (1) . a Pass through the interior door handle cable (2) . a Firmly apply the film around its complete edge. a Check the water seal before refitting the door trim (see Technical Note 0653A, Bodywork fault fin- ding: Water sealing tests). a Refit the door trim( (see Front side door trim: Re- moval – Refitting) (MR 393, 72A, Side opening ele- ments trim) or( (see Rear side door trim: Removal – Refitting) (MR 393, 72A, Side opening elements trim).
REMOVAL a Note: The sealing ?lm can only be used once; it is des- troyed when it is removed. It is essential to replace the ?lm with a new one each time it is removed. REMOVING THE SEALING FILM a Remove the door trim( (see Front side door trim: Removal – Refitting) (MR 393, 72A, Side opening elements trim) or( (see Rear side door trim: Remo- val – Refitting) (MR 393, 72A, Side opening ele- ments trim). a Start with the upper section of the sealing film. a Remove the heptane in small amounts between the film and the inner door panel as the film peels away (pull slowly on the sealing film). a Carefully strip off the sealing film taking care not to tear it. REFITTING a Note: Remove the adhesive residue from the inner door panel by sticking wide masking tape over the adhesive residue. Pull gently on the masking tape to remove any adhesive residue. Clean the inner door panel with heptane using a dr y, lint-free cloth. WARNING The door must be clean (free of dust, grease, anti-adhesive products), with no trace of impuri- ties and no condensation. The area of the inner door panel where the ?lm is applied must be painted completely. Adhesive surfaces should be at a minimum tem- perature of 15? in order for the ?lm to adhere pro- perly to the door. 116833 a Unclip the interior handle mounting (if the vehicle is fitted with one) using an unclipping tool. 1 – First procedure a Strip off the sealing film using a hot air gun set to ap- proximately 100? and approximately 20 cm from the film, directing the hot air flow onto the edge of the film. a Start by stripping off a corner of the sealing film. a Carefully strip off the sealing film taking care not to tear it. 2 – Second procedure a Remove the sealing film using a syringe filled with heptane. Front side door ACCESS FLAP 1 – Opening access flaps front side door 111932 Rear side door a Note: The front side door sealing ?lm incorporates two access ?aps to access the various door compo- nents and to allow the door to be straightened. Cut according to the marking on the sealing ?lm depending on the operation being performed. Depending on the operations being performed, it may be necessary to make cuts locally at the various mountings (bolts or nuts). 111945 a Position the sealing film using the guide points (1) . a Pass through the interior door handle cable (2) . a Firmly apply the film around its complete edge. a Check the water seal before refitting the door trim (see Technical Note 0653A, Bodywork fault fin- ding: Water sealing tests). a Refit the door trim( (see Front side door trim: Re- moval – Refitting) (MR 393, 72A, Side opening ele- ments trim) or( (see Rear side door trim: Removal – Refitting) (MR 393, 72A, Side opening elements trim).
Tags: renault
